| **FOR ENTERTAINMENT ONLY**
DO NOT USE FOR FLIGHT TRAINING
ONLY CONSULT YOUR APPROVED TRAINING MATERIAL/POH/OPERATOR GUIDANCE
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
737 Checklist + Virtual PM for use with the Zibo 737 and XChecklist Plugin
Tested in 12.03r1 using the Zibo v3.55
Based off the Thompson Airways QRH
Procedures have been adjusted to work with the limtiations of XChecklist and the Zibo Mod
AGAIN - DO NOT USE FOR INSTRUCTION IF YOU ARE ON YOUR TYPE RATING
NORMAL CHECKLISTS:
- Preflight
- Before Start
- Before Taxi
- Before Takeoff
- After Takeoff
- Descent
- Approach
- After Landing
- Shutdown
- Secure
QAI NNCs:
- Aborted Engine Start
- Airspeed Unreliable
- APU Fire
- Dual Engine Failure
- Engine Failure
- Engine Fire
- Engine Limit or Surge or Stall
- Engine Severe Damage or Separation
- Engine Tailpipe Fire
- Evacuation
- Emergency Descent
- Runaway Stabilizer
- Smoke, Fire or Fumes
- Smoke, Fire, or Fumes Removal
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
FEATURES
Full dynamic functionality, including fault callouts and prompts for QAI memory items. The clist file will detect when failures occur and give an automatic callout. This will then prompt memory items (if applicable) and then the checklist. Items will check themselves as they are completed (for this to work, you'll need the Virtual F/O option selected in your XChecklist Setup). Some options are necessarily non-dynamic to reflect the agreements you (PF) and PM would need to make IRL.
I wrote this mod so that you can have the experience of flying the plane with failures ON without the fear of not knowing what to do when something goes wrong.
Watch this video to see this in action with an EFATO.
Recommended Study:
737NG QRH Memory Items
737NG QRH
flightdeck2sim NNC Tutorials
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
INSTALLATION INSTRUCTIONS
1. Unzip the file
2. Copy ONLY the clist.txt file into your Zibo 737 folder:
Ex. C:\Downloads\Zibo 737 XChecklist >>>> C:\Desktop\X-Plane 12\Aircraft\Laminar Research\B737-800X
3. Launch X-Plane
4. Open XChecklist Setup (plugins, XChecklist, Setup)
5. Tick 'Virtual F/O'
6. [Recommended] Tick 'Translucent Window'
7. [Recommended] Setup a key/controller shortcut to tick items (I'm using the trigger on my joystick).
8. Enjoy!
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
KNOWN LIMITATIONS
- As shown in the video, because of the limitations of XChecklist, fulfilling non-applicable "If" conditionals (ex. "If the engine fire light is illuminated" and it is not illuminated) requires you to manually tick the option.
- The runaway stabilizer failure currently DOES NOT work in the Zibo Mod. Therefore, while it exists, activating the failure in X-Plane failures will not trigger this item as it does not cause a runaway. (If you have a look inside the clist you can see what is triggering it and why it isn't going off.)
I've tried to test it in as many different scenarios as possible for the failures but there may be unforeseen bugs. If you find a bug, please report it on the forum so I can work on a fix.
Feedback is very welcome. I am planning to add Windshear & Terrain Escape, RTO, and G/A callouts in future, time permitting.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------CHANGELOG
V1.01 (23-04-2023):
Corrected bug with smoke detection dataref (previously testing the lights would trigger the warning).
Added dynamic checks for 'V-speeds set'.
Added dynamic check for anti-ice (checks OAT against ENG anti-ice switch position).
Changed datarefs used for checking flap lever position and indicated flap setting.
Vær den første til at kommentere.